|
DNC / file transfer settings
for Fanuc 10,11,12,15
|
| Set the following parameters on the machine:
Parameter |
Value |
| 5001 | 1 |
| 5002 | 2 |
| 5003 | 3 |
| 5110 | 4 |
| 5111 | 2 |
| 5112 |
9 (2400) |
| 5120 | 4 |
| 5121 | 2 |
| 5122 | 9 |
| 5130 | 4 |
| 5131 | 2 |
| 5132 | 9 |
| TV Check | 0 (off) |
| Punch code | 0 (ISO) |
| Input device | 1 (RS232C) |
| Output device | 1 (RS232C) |
To set the CNC up for drip feed:
Set "Tape mode" on.
Dripfeed facility on the Fanuc must be enabled.
Send the program from the computer, then press Cycle Start on the Fanuc. To pause dripfeed, turn the Feedrate override to 0%.
Set ConnectCNC as follows:
Common Settings |
| Name |
Fanuc |
| Baudrate |
2400 (or to match CNC setting) |
| Data bits |
7 |
| Stop bits |
2 |
| Parity |
Even |
| Flow control | Xon/Xoff |
| Xon Char. | 17 |
| Xoff char. | 19 |
| Port | as available |
Send Settings |
| Header String | 37,13,10 |
| Trailer String | 37,13,10 |
The above codes mean "%,CR,LF".
If your program has the percent sign at the beginning and end, leave the Header and Trailer blank. |
End of Line Sequence |
| Recognize custom EOL |
|
| Replace |
|
 |
| Check "%" character | checked if you have a "%" at the beginning and end of your programs. |
| Skip empty lines | user's choice |
| Skip line numbers | user's choice |
| Skip non printable bytes | user's choice |
| Skip comments |
check "(...)" if required |
| Default folder | Folder in which you store this machine's programs |
| Start transfer delay | user's choice |
Receive Settings |
| Header String |
|
| Trailer String |
|
End of Line Sequence |
| Recognize custom EOL |
|
| Replace (checked) |
13,10 |
|
| Check "%" character | checked if you have a "%" at the beginning and end of your programs. |
| Skip empty lines | user's choice |
| Skip line numbers | user's choice |
| Skip non printable bytes | user's choice |
| Skip comments |
check "(...)" if required |
| Default folder | Folder in which you store this machine's programs |
| Start transfer delay | user's choice |
Cable Pin Out
|
Once you have ConnectCNC and your CNC machines communicating, we strongly suggest you take the following precautions:
- Download some programs, the longer the better, from your CNC to the
pc. Save them under a temporary filename so you don't overwrite the original
files. Examine themfor errors such as dropped or changed text.
Do this for the first few programs that you use.
|
These settings have been collected from users of
our software and machine tool distributers. We have listed them to
help users of ConnectCNC to communicate between their computers and
CNC controls.
Since we have no control over the many variables involved, including
such things as cable conditions, modifications to machines, condition
of computer hardware, etc., we take no responsibility for any damage
caused to programs or machines through the use of this software.
|
|
Site
Map
©Copyright CNC Consulting Inc. 1996-2008
|
| Minimum system requirements for our software:
Any computer with Windows95 v950B or higher(32 bit), 98, ME, 2000 XP, NT, Vista.
Hardware requirements will depend on the size of CNC files processed with
EditCNC and ConnectCNC.
However, ConnectCNC requires at least one serial
COM port, or USB/RS232c port converter.
|